#Router configuration pdf how to
#Router configuration pdf software
#Router configuration pdf password

We will follow the same instructions as step 5 to configure fast ethernet port 0/1. Set IP address of interface Fastethernet 0/1 to be 192.168.0.254/26 While in global configuration command mode typeД¦. The вЂњexitвЂќ command will drop us back into the global configuration command mode. To accomplish this objective we must enter the interface configuration command mode for fast ethernet port 0/0 and set the interfaceвЂ™s IP address as well as its subnet mask. The first useable IP address of the 10.0.0.0/30 network is 10.0.0.1. Set IP address of interface Fastethernet 0/0 to be the first address of network 10.0.0.0/30 Note: The вЂњexitвЂќ command will drop you down into the global configuration command mode.ДҐ. They appear in the configuration as line vty 0 4вЂќ ().

#Router configuration pdf software

They are virtual, in the sense that they are a function of software вЂ“ there is no hardware associated with them.

вЂњThe VTY lines are the Virtual Terminal lines of the router, used solely to control inbound Telnet connections. You will then be dropped down into the privileged EXEC command mode after entering the вЂњendвЂќ command.

#Router configuration pdf password

This password will deter unauthorized access to the router via the console connection. In global configuration mode enter вЂњenable secret ranetenablepassвЂќ. After pressing enter you will see the prompt change from вЂњRouter(config)#вЂќ to вЂњRanetA(config)#вЂќ. Once in the global configuration mode, type вЂњhostnameвЂќ followed by a space and the new router name which is вЂњRanetAвЂќ. Telnet from Ranet PC to Ranet A by using IPДЄddress 192.168.0.254 and telnet password Both interface Fastethernet 0/0 and 0/1 mustДЄfter configuring this, you should be able toДў. Set IP address of interface Fastethernet 0/1 toД§. Set IP address of interface Fastethernet 0/0 toД«e the first address of network 10.0.0.0/30Д¦. Set telnet password to be вЂњranettelnetpassвЂќДҐ. Set console password to be вЂњranetconsolepassвЂќД¤. Set enable secret to be вЂњranetenablepassвЂќДЈ. You have to do the basic configuration via Console TerminalДў. We have just installed a new router to be our gateway.

You are the Network Administrator at Ranet. Below are the labвЂ™s scenario and instructions: We are now prepared to enter the commands to complete the lab. Global configuration command mode and is entered by typing вЂњconfigure terminalвЂќ. This is the PC that has a console (light blue) cable connected to the router that will be configured. When the lab launches, click on вЂњPC-PT Console TerminalвЂќ. You must use the PC to open a terminal (console) session to the router in order to configure it via the command line interface (CLI). The way this lab has been setup resembles how you would configure a router in actuality.

#Router configuration pdf how to

Before we get started, I will explain how to configure routers in the Packet Tracer lab environment. I will walk you through all of the commands to accomplish each objective of this lab. This first lab (1-1) covers basic Cisco router network configuration. For details from Cisco on configuring Telnet, Console and AUX passwords, click here.

For documentation about basic router configuration from Cisco, visit their page. A list of download links to 19 of these labs is about half way down this page. A good practice method for the CCNA exam (Cisco Certified Networking Associate) if you have the Cisco study tool Packet Tracer is to download some practice labs that cover the CCNA objectives.